Our DC gear motors are considered powerhouses with a compact design. The DC motors feature a worm gear and selection options in the drive's wrench sizes.
In addition to being used as drives in ergonomic table applications, the gearmotors
can be used universally due to their size and minimal noise
characteristics. Our range is diverse and offers the optimum solution
for a wide variety of requirements. In addition, there are complementary
products to the gearmotors in our store, such as spindle drives, motor cablesandhand controls.
Rated torque 3 Nm
Idle speed 150 rpm
Outer dimensions 150x76x40 mm .
Drive inside hexagon SW6/SW7/SW8
Powerful 24 V DC motor with 2-stage worm gear with a continuous internal hexagon on the output. The motor cable with AMP plug and the integrated Hall-sensors allow secure connection and exact positioning of the entire system. The included cable can be ordered here as a spare part.
Special features
Two integrated Hall-sensors for measurement of the revolutions and direction of rotation
Through going hexagon socket in wrench widths 6 mm, 7 mm, 8 mm
Good self-locking properties
220 mm + 1750 mm motor cable with connector included
Can be combined with most Ketterer spindle systems
Technical notes
Please note the correct installation position of the drive! The drive is correctly mounted when it turns counterclockwise under load (see installation position/mounting).
The drive working range (nominal torque) is determined for a service life of 10.000 double strokes.
Through the controller* the system is regulated such that the speed in the entire drive working range is kept as constant as possible.
By using a controller with a short-circuit brake the holding torque position of the drive can be increased.* In combination with LogicData control box Compact-3
Model
3121.00-2002
3121.00-2007
3121.00-2008
Motor
DC Motor 24 V
DC Motor 24 V
DC Motor 24 V
Sensor/Power supply
Hall/5 V DC/0,3 A
Hall/5 V DC/0,3 A
Hall/5 V DC/0,3 A
Protection class
IP30
IP30
IP30
Idle running speed
150 rpm (24 V)
150 rpm (24 V)
150 rpm (24 V)
Duty cycle idle speed
20% (at 5 min.)
20% (at 5 min.)
20% (at 5 min.)
Rated torque*
3 Nm
3 Nm
3 Nm
Duty cycle nominal load*
20 s ON 240 s OFF
20 s ON 240 s OFF
20 s ON 240 s OFF
Short term peak torque (<1sec)
4,5 Nm
4,5 Nm
4,5 Nm
Input
hex 6mm
hex 7mm
hex 8mm
*Load determined for service life of 10.000 double strokes
Powerful 24 V DC motor with
2-stage worm gear with a continuous internal hexagon on the output. The motor
cable with AMP plug and the integrated Hall-sensors allow secure connection and
exact positioning of the entire system. The included cable can be ordered here as a spare part.Special featuresTwo integrated Hall-sensors for measurement of the
revolutions and direction of rotationThrough going hexagon socket in wrench widths 6 mm, 7
mm, 8 mmGood self-locking properties220 mm + 1750 mm motor cable with connector includedCan be combined with most Ketterer spindle systems
Technical notesPlease note the correct installation position of the
drive! The drive is correctly mounted when it turns counterclockwise under load
(see installation position/mounting).The drive working range (nominal torque) is determined
for a service life of 10.000 double strokes.Through the controller* the system is regulated such
that the speed in the entire drive working range is kept as constant as
possible.By using a controller with a short-circuit brake the
holding torque position of the drive can be increased.* In combination with
LogicData control box Compact-3
Model3121.00-10023121.00-10033121.00-1004MotorDC Motor 24 VDC Motor 24 VDC Motor 24 VSensor/Power supplyHall/5 V DC/0,3 AHall/5 V DC/0,3 AHall/5 V DC/0,3 AProtection classIP30IP30IP30Idle running speed150 rpm (24 V)150 rpm (24 V)150 rpm (24 V)Duty cycle idle speed20% (at 5 min.)20% (at 5 min.)20% (at 5 min.)Rated torque*2,5 Nm2,5 Nm2,5 NmDuty cycle nominal load*20 s ON 240 s OFF20 s ON 240 s OFF20 s ON 240 s OFFShort term peak torque (<1sec)4,5 Nm4,5 Nm4,5 NmInputhex 6mmhex 7mmhex 8mm *
Load determined for service life of 10.000 double strokes
Compact 24 V DC motor with worm
gear and a continuous internal hexagon. Optimized sound characteristics due to
elastic coupling and vibration damping fastening elements. Although the drive
was developed for ergonomic table applications, it can be used in many other
fields. The drive is designed and tested for axial pressure load. A cable with AMP
plug and an integrated Hall-sensor allows easy and secure control of the entire
system. The included cable can be ordered here as a spare part. You can also order the matching spindle unit with motor adapter in our store.Special featuresVibration and sound-damped design through mechanical
decoupling of the spindle systemTwo integrated Hall sensors for measurement of the
revolutions and direction of rotationThrough going hexagon socket in wrench widths 6 mm and
7 mmGood self-locking properties100 mm + 1750 mm motor cable with connector includedCan be combined with most Ketterer spindle systems
Variant keyThe variants are formed by the
different wrench widths and by fastening variants with and without fastening
plate (Variant A or Variant B).Technical notesThe drive working range (nominal torque) is determined
for a service life of 10,000 double strokes.Through the controller* the system is regulated such
that the speed in the entire drive working range is kept as constant as
possible.By using a controller with a short-circuit brake the
holding torque position of the drive can be increased.
* In combination with LogicData control box Compact-3 Model3130.00-1002 Variante B3130.00-1003 Variante B3130.00-2002 Variante A3130.00-2003 Variante AMotorDC Motor 24 VDC Motor 24 VDC Motor 24 VDC Motor 24 VSensor/Power supplyHall/5 V DC/0,3 AHall/5 V DC/0,3 AHall/5 V DC/0,3 AHall/5 V DC/0,3 AProtection classIP30IP30IP30IP30Idle running speed120 rpm (24 V)120 rpm (24 V)120 rpm (24 V)120 rpm (24 V)Duty cycle with idle running20% (at 5 Min.)20% (at 5 Min.)20% (at 5 Min.)20% (at 5 Min.)Rated torque*3,5 Nm3,5 Nm3,5 Nm3,5 NmDuty cycle with 3,5 Nm*20 sec ON 240 sec OFF20 sec ON 240 sec OFF20 sec ON 240 sec OFF20 sec ON 240 sec OFFShort-term peak torque (<1sec)6 Nm6 Nm6 Nm6 NmInputhex 6mmhex 6mmhex 6mmhex 7mm* Determined at full load for service life of 10,000 double strokes
Compact 24 V DC motor with worm gear and continuous internal hexagon. Although the drive was developed for ergonomic table applications, it can be used in many other fields as well. A cable with AMP plug and an integrated Hall-sensor allows an easy and secure control of the entire system.Special featuresTwo integrated Hall-sensors for measurement of the revolutions and direction of rotationContinuous internal hexagon in wrench widths 6 mm, 7 mm, 9 mmGood self-locking propertiesLow noise100 mm + 1750 mm motor cable with connector includedCan be combined with most Ketterer spindle systemsTechnical notesTo ensure secure operation the motor must be operated in the predefined installation position (see installation position/mounting).The drive working range (nominal torque) is determined for a service life of 10,000 double strokes.The connection position of the drive in the entire system with vibration damping elements can be beneficial. However, the functional reliability position of the drive in the application should be tested.Through the controller* the system is regulated such that the speed in the entire drive working range is kept as constant as possible.By using a controller with a short-circuit brake the holding torque position of the drive can be increased.* In combination with LogicData control box Compact-3 Model3133.00-10023133.00-10033133.00-1009Versionwith brakewith brakewith brakeMotorDC Motor 24 VDC Motor 24 VDC Motor 24 VSensor/Power supplyHall/5 V DC/0,3 AHall/5 V DC/0,3 AHall/5 V DC/0,3 AProtection classIP30IP30IP30Idle running speed120 rpm (24 V)120 rpm (24 V)120 rpm (24 V)Duty cycle with idle running20% (at 5 Min.)20% (at 5 Min.)20% (at 5 Min.)Rated torque*2,5 Nm2,5 Nm2,5 NmDuty cycle with 3,5 Nm20 sec ON 4min. OFF20 sec ON 4min. OFF20 sec ON 4min. OFFShort-term peak torque (< 1 sec)5 Nm5 Nm5 NmInputhex 6mmhex 7 mmhex 9 mmModel3133.00-00163133.00-00173133.00-0011Versionwithout brakewithout brakewithout brakeMotorDC Motor 24 VDC Motor 24 VDC Motor 24 VSensor/Power supplyHall/5 V DC/0,3 AHall/5 V DC/0,3 AHall/5 V DC/0,3 AProtection glassIP30IP30IP30Idle running speed120 rpm (24 V)120 rpm (24 V)120 rpm (24 V)Duty cycle with idle running20% (at 5 Min.)20% (at 5 Min.)20% (at 5 Min.)Rated torque*3,5 Nm3,5 Nm3,5 NmDuty cycle with 3,5 Nm*20 sec ON 4min. OFF20 sec ON 4min. OFF20 sec ON 4min. OFFShort-term peak torque (< 1 sec)5 Nm5 Nm5 NmInputhex 6 mmhex 7 mmhex 9 mm* Determined at full load for service life of 10.000 double strokes
Compact 24 V DC motor with worm gear and a continuous internal
hexagon. Although the drive was developed for ergonomic table applications, it
can be used in many other fields. A cable with AMP plug and an integrated
Hall-sensor allows easy and secure control of the entire system. The included cable can be ordered here as a spare part. You can also order the matching spindle unit with motor adapter in our store.Special featuresTwo integrated Hall-sensors for measurement
of the revolutions and direction of rotationThrough going hexagon socket in wrench
widths 6 mm and 9 mmGood self-locking propertiesLow noise1000 mm
+ 1750 mm motor cable with connector includedCan be combined with all Ketterer spindle
systems
Technical notesThe drive working range (nominal torque) is
determined for a service life of 10.000 double strokes.Through the controller* the system is
regulated such that the speed in the entire drive working range is kept as constant
as possible.By using a controller with a short-circuit
brake the holding torque position of the drive can be increased. *In combination with LogicData control box Compact-3 Model3133.48-00093133.48-0016MotorDC Motor 24 VDC Motor 24 VSensor/Power supplyHall/5 V DC/0,3 AHall/5 V DC/0,3 AProtection classIP30IP30Duty cycle idle speed20% (at 5 Min.)20% (at 5 Min.)Idle running speed100 rpm (24 V)100 rpm (24 V)Rated torque*5 Nm5 NmDuty cycle nominal load20 s ON/ 240 s OFF20 s ON/ 240 s OFFShort term peak torque (<1sec)8 Nm8 NmInputhex 9mmhex 6mm * Load determined for service life of 10.000 double strokes
Compact 24 V DC motor with worm gear and continuous internal hexagon. Although the drive was developed for ergonomic table applications, it can be used in many other fields as well. A cable with AMP plug and an integrated Hall-sensor allows an easy and secure control of the entire system. You can find a suitable spindle unit with motor adapter here.
Special features
Two integrated Hall-sensors for measurement of the revolutions and direction of rotation
Continuous internal hexagon in wrench widths 6 mm, 7 mm, 9 mm
Good self-locking properties
Low noise
100 mm + 1750 mm motor cable with connector included
Can be combined with most Ketterer spindle systems
Technical notes
To ensure secure operation the motor must be operated in the predefined installation position (see installation position/mounting).
The drive working range (nominal torque) is determined for a service life of 10,000 double strokes.
The connection position of the drive in the entire system with vibration damping elements can be beneficial. However, the functional reliability position of the drive in the application should be tested.
Through the controller* the system is regulated such that the speed in the entire drive working range is kept as constant as possible.
By using a controller with a short-circuit brake the holding torque position of the drive can be increased.
* In combination with LogicData control box Compact-3
Model
3133.00-0002
3133.00-0003
3133.00-0001
Version
with brake
with brake
with brake
Motor
DC Motor 24 V
DC Motor 24 V
DC Motor 24 V
Sensor/Power supply
Hall/5 V DC/0,3 A
Hall/5 V DC/0,3 A
Hall/5 V DC/0,3 A
Protection class
IP30
IP30
IP30
Idle running speed
120 rpm (24 V)
120 rpm (24 V)
120 rpm (24 V)
Duty cycle with idle running
20% (at 5 Min.)
20% (at 5 Min.)
20% (at 5 Min.)
Rated torque*
2,5 Nm
2,5 Nm
2,5 Nm
Duty cycle with 3,5 Nm*
20 sec ON 4min. OFF
20 sec ON 4min. OFF
20 sec ON 4min. OFF
Short-term peak torque (< 1 sec)
5 Nm
5 Nm
5 Nm
Input
hex 6mm
hex 6 mm
hex 6 mm
Model
3133.00-0014
3133.00-0010
3133.00-0012
Version
without brake
without brake
without brake
Motor
DC Motor 24 V
DC Motor 24 V
DC Motor 24 V
Sensor/Power supply
Hall/5 V DC/0,3 A
Hall/5 V DC/0,3 A
Hall/5 V DC/0,3 A
Protection glass
IP30
IP30
IP30
Idle running speed
120 rpm (24 V)
120 rpm (24 V)
120 rpm (24 V)
Duty cycle with idle running
20% (at 5 Min.)
20% (at 5 Min.)
20% (at 5 Min.)
Rated torque*
3,5 Nm
3,5 Nm
3,5 Nm
Duty cycle with 3,5 Nm*
20 sec ON 4min. OFF
20 sec ON 4min. OFF
20 sec ON 4min. OFF
Short-term peak torque (< 1 sec)
5 Nm
5 Nm
5 Nm
Input
hex 6 mm
hex 7 mm
hex 9 mm
* Determined at full load for service life of 10.000 double strokes
Nominal torque 5 Nm
Idle speed 115 rpm
1 common drive variant
Drive inside hexagonal SW 6 or SW7
Features DC geared motor
Compact motor drive with one continuous hexagon socket.The gear motor serves as a simple upgrade from the manually operated variant to the electric motor solution
Series
3143.00-1015
3143.00-1041
Motor operating voltage
6 - 30 V
6 - 30 V
Motor rated voltage
18 V
18 V
Drive:
inside 6kt SW6
inside 6kt SW7
Gear number:
1 common
1 common
Duty cycle
20% (bei 5 Min.)
20% (bei 5 Min.)
Protection class
IP 30
IP 30
Idle speed
115 U/min
115 U/min
max drive torque
5 Nm
5 Nm
Rated current
3,3 A bei 5 Nm
3,3 A bei 5 Nm
Weight:
981 g
981 g
Motor cable:
2 strands L50mm
2 strands L50mm
Powerful DC motor with worm gear and continuous hexagon socket. The drive was developed for ergonomic table applications, but is also used in many other areas.
Special features DC geared motor
Continuous hexagon socket in width across flats SW6 / SW7
Good self-locking properties
Can be combined with all Ketterer spindle systems
Technical information DC geared motor
The working range of the drive (nominal torque) is determined at the service life of 10,000 double strokes.
By using a control with short-circuit brake, the holding torque of the drive can be significantly increased.
Features DC geared motor
Compact motor drive with a continuous hexagon socket and integrated displacement encoder. The geared motor can be ordered with an idle speed of 115 rpm or 230 rpm.
The geared motor serves as a simple upgrade from the manually operated version to the electric motor solution. The motor is supplied with a matching cable.
Series
3143.00-1002
3143.00-1003
3143.00-1006
3143.00-1008
Motor operating range
6 - 30 V
6 - 30 V
6 - 30 V
6 - 30 V
Motor Nennbereich
18 V
18 V
18 V
18 V
Motor nominal range
inside 6kt SW6
inside 6kt SW7
inside 6kt SW6
inside 6kt SW7
Gear ratio:
1 gängig
1 gängig
2 gängig
2 gängig
Duty cycle
20% (bei 5 Min.)
20% (bei 5 Min.)
20% (bei 5 Min.)
20% (bei 5 Min.)
Sensor/Supply
Hall/ 5 V DC/ 0,3 A
Hall/ 5 V DC/ 0,3 A
Hall/ 5 V DC/ 0,3 A
Hall/ 5 V DC/ 0,3 A
Protection class
IP 30
IP 30
IP 30
IP 30
Idle speed
115 U/min
115 U/min
230 U/min
230 U/min
max drive torque
5 Nm
5 Nm
5 Nm
5 Nm
Rated current
3,3 A bei 5 Nm
3,3 A bei 5 Nm
4,2 A bei 2,8 Nm
4,2 A bei 2,8 Nm
Weight:
988 g
987 g
982 g
982 g
special features
integrated measuring system
integrated measuring system
integrated measuring system
integrated measuring system
Motor cable:
Included in delivery
Included in delivery
Included in delivery
Included in delivery
Complementary articles / spare parts DC gear motor 18V
Motor cable 1950mm or 1000mm / with or without invert power/sensors
Motor cable 1950mm / with 90° plug
Motor cable 1950mm or 1000mm / Compact KTS
zurück zur Übersicht
Powerful DC motor with worm gear and a continuous internal hexagon. Although the drive was developed for ergonomic table applications, it can be used in many other fields. A cable with AMP plug and an integrated Hall-sensor allows an easy and secure control of the entire system.
For extension/spare part the following cables are available in different lengths:
Motor cable in 1950mm or 1000mm / with or without invert power/sensors
Motor cable in 1950mm / with 90° plug
Motor cable in 1950mm or 1000mm / Compact KTS
Special features
Two integrated Hall-sensors for measurement of the revolutions and direction of rotation
Through going hexagon socket in wrench widths 6 mm, 7 mm, 9 mm
Available as “power package” or as “high speed” variant
1000 mm motor cable with connector included
Good self-locking properties
Can be combined with all Ketterer spindle systems
Technical notes
The drives working range (nominal torque) is determined for a service life of 10.000 double strokes.
Through the controller* the system is regulated such that the speed in the entire drive working range is kept as constant as possible.
By using a controller with a short-circuit brake the holding torque position of the drive can be increased.* In combination with LogicData control box Compact-3
Model
3143.00-2002
3143.00-2003
3143.00-2012
3143.00-2013
Operating voltage
6 - 30 V
6 - 30 V
6 - 30 V
6 - 30 V
Rated voltage
24 V
24 V
24 V
24 V
Sensor/Power supply
Hall/5 V DC/0,3 A
Hall/5 V DC/0,3 A
Hall/5 V DC/0,3 A
Hall/5 V DC/0,3 A
Electric current
5,5 A at 5 Nm
5,5 A at 5 Nm
4,2 A at 2,8 N
4,2 A at 2,8 Nm
Protection class
IP30
IP30
IP30
IP30
Idle running speed
115 rpm (24 V) 120 rpm*
115 rpm (24 V) 120 rpm*
230 rpm (24 V) 240 rpm*
230 rpm (24 V) 240 rpm*
Duty cycle idle speed
20% (at 5 Min.)
20% (at 5 Min.)
20% (at 5 Min.)
20% (at 5 Min.)
Rated torque*
5 Nm
5 Nm
2,8 Nm
2,8 Nm
Duty cycle nominal load**
20 s ON 240 s OFF
20 s ON 240 s OFF
20 s ON 240 s OFF
20 s ON 240 s OFF
Short term peak torque (<1s)
9 Nm
9 Nm
5 Nm
5 Nm
Input
hex 6mm
hex 7mm
hex 6mm
hex 7mm
* In combination with LogicData control box Compact-3 ** Load determined for service life of 10.000 double strokes
Rated torque 3 Nm
Idle speed 150 rpm
Outer dimensions 150x76x40 mm .
Drive inside hexagonSW7
with brake
Powerful 24 V DC motor with 2-stage worm gear with a continuous internal hexagon on the output. The motor cable with AMP plug and the integrated Hall-sensors allow secure connection and exact positioning of the entire system. The included cable can be ordered here as a spare part.
Special features
Two integrated Hall-sensors for measurement of the revolutions and direction of rotation
Through going hexagon socket in wrench widths 7 mm
with brake
Good self-locking properties
220 mm + 1750 mm motor cable with connector included
Can be combined with most Ketterer spindle systems
Technical notes
Please note the correct installation position of the drive! The drive is correctly mounted when it turns counterclockwise under load (see installation position/mounting).
The drive working range (nominal torque) is determined for a service life of 10.000 double strokes.
Through the controller* the system is regulated such that the speed in the entire drive working range is kept as constant as possible.
By using a controller with a short-circuit brake the holding torque position of the drive can be increased.* In combination with LogicData control box Compact-3
Model
3121.00-2009
Motor
DC Motor 24 V
Sensor/Power supply
Hall/5 V DC/0,3 A
Protection class
IP30
Idle running speed
150 rpm (24 V)
Duty cycle idle speed
20% (at 5 min.)
Rated torque*
3 Nm
Duty cycle nominal load*
20 s ON 240 s OFF
Short term peak torque (<1sec)
4,5 Nm
Input
hex 7mm
*Load determined for service life of 10.000 double strokes
Idle speed 270 rpm l Traversing speed 12-45 mm/s l For push and pull movements l Powerful 24 V DC motor with worm gear unit
Features Motor drive for through-spindle 4778
Powerful 24 V DC motor with worm gear, designed for non-rotating through-spindle for push and pull movements.
A cable with AMP connector and integrated Hall sensors allow simple and safe control of the entire system.
Special features
Two integrated Hall sensors for detecting rotations and the direction of rotation
Various types of internal thread for continuous spindle
Good self-locking properties
Fast and powerful
Spindle must be ordered separately
Series
4778.00-0002
4778.00-0004
4778.00-0006
Drive motor
DC Motor 24 V
DC Motor 24 V
DC Motor 24 V
Sensor / supply
Hall/5 V DC/0,3 A
Hall/5 V DC/0,3 A
Hall/5 V DC/0,3 A
Protection class
IP30
IP30
IP30
Operating temperature
0° bis +30°
0° bis +30°
0° bis +30°
Electric current (IN) at max. load
8 A
8 A
8 A
Idle running speed
270 U/min
270 U/min
270 U/min
Duty cycle idle speed
20% (bei 5 Min.)
20% (bei 5 Min.)
20% (bei 5 Min.)
Duty cycle at max. load
10 s ON 240 s OFF
13 s ON 240 s OFF
8 s ON 240 s OFF
Max. lifting force*
1900 N
3700 N
950 N
Traverse speed (constant from F= 0 bis Fmax.)**
24mm / s
12 mm / s
45 mm / s
Static Self locking ***
200 kg
380 kg
200 kg
Output (Inner thread)
SG16x8P4 RH
Tr16x4 RH
SG14x16P4 RH
* Determined for service life of 10,000 double strokes** The controller regulates the system in such a way that the travel speed in the entire drive working range is kept as constant as possible*** In combination with controller, which has a short circuit brake
Technical information
The spindle is not included in the scope of delivery and must be ordered separately
Attention: It is essential to observe the correct installation position (see installation example).
The drive must be protected against the effects of lateral forces by a separate guide system.
The operating range of the drive (rated torque) is determined for a service life of 10,000 double strokes.
The holding torque of the drive can be increased by using a control unit with a short-circuit brake.
€233.24*
This website uses cookies to ensure the best experience possible. More information...